Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
techtalk:evo:body04 [2019/02/26 13:01] – [Kickstand] ixl2relaxtechtalk:evo:body05 [2024/01/02 18:27] (current) – hippysmack
Line 5: Line 5:
  
 ===== Sub-Documents ===== ===== Sub-Documents =====
-* . . . [[techtalk:evo:body04a|2009 HD XL 1200C Shift Lever Assembly Modification]]+ 
 +* . . . [[techtalk:evo:body05a|2009 HD XL 1200C Shift Lever Assembly Modification]]
  
 \\ \\
 +See [[techtalk:ref:body30|Foot Controls, Pegs, Kickstand]] in the REF section of the Sportsterpedia for more foot control and peg mods. \\
  
 ====== Pegs ===== ====== Pegs =====
Line 15: Line 17:
 ====== Kickstand ====== ====== Kickstand ======
  
-It looks like 1998 was the first year for the kickstand bushings\\ +{{  :techtalk:evo:body:kickstand-bushing--worn-byjohnk.jpg?400|}}\\ 
-- The 1998 parts were still the same as previous model year:\\+The 1998 model year was the first for using the kickstand bushings - The rest of the 1998 parts were the exact same as the previous model years:\\
  
 +**__Stock Parts__**\\
 50003-89A . PIN, CLEVIS\\ 50003-89A . PIN, CLEVIS\\
 50005-85A . SPRING, JIFFY STAND\\ 50005-85A . SPRING, JIFFY STAND\\
-50006-89 . . JIFFY STAND\\+50006-89 . . JIFFY STAND (varied by model)\\ 
 + 
 +but these bushings were added:\\ 
 +53176-08 . . BUSHING (2ea)\\ 
 +(previously 53158-98)\\ 
 +{{  :techtalk:evo:body:kickstand-pivot-pin-byil67bp.jpg?400|}}\\ 
 +It seems the holes in the kickstand mounting tab at the frame were enlarged from that model year forward to accomodate the bushings. There are two bushings used - one above and the other below - between the pivot pin and the mounting tab. The bushings should be checked every year to see if they need replacing due to wear (such as shown in this picture.) 
 + 
 +The stock configuration has the pivot pin inserted from below & a cotter pin put thru the end of the pivot pin at the top. With this arrangement, if the cotter pin wears out or breaks, the pivot pin will drop from the mount & may completely be lost, along with the kick stand. It's been suggested that the pivot pin should be inserted from the top with the cotter pin at the bottom, so if the cotter pin is gone, the pivot pin remains in the mount. However, in this arrangement, the cotter pin is exposed to the spring movement past the bottom of the pivot pin, which occurs whenever the kickstand is applied or retracted. It's your choice. 
 + 
 +(See this [[https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-suspension-frame-forks-handlebars-fuel-tank-oil-tank-fenders/149182-kickstand-spring-replacement-what-i-did?t=1618492|discussion on the XLForum]]) 
 + 
 +(See the [[techtalk:ref:body30#kickstand_spring_alternative|alternative spring choice]] in the REF Section)\\ 
 +(See the [[techtalk:ref:body30#kickstand_bushings_alternative|alternative kickstand bushings]] in the REF Section)\\ 
 + 
 +Inspect and grease the Jiffy Stand and parts periodically. \\ 
 +This one looked to have wear and upon dis-assembly a bushing was found to be broken. \\ 
 +{{:techtalk:evo:body:jiffy_stand_by_matty.jpg?direct&300|}} ((photo by Matty of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-suspension-frame-forks-handlebars-fuel-tank-oil-tank-fenders/152531-jiffy-stand/page2?s=771e0679782951ace27913a1baf5a1e0&t=1643796&page=2)) {{:techtalk:evo:body:jiffy_stand_parts_1_by_matty.jpg?direct&300|}} ((photo by Matty of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-suspension-frame-forks-handlebars-fuel-tank-oil-tank-fenders/152531-jiffy-stand/page3?s=771e0679782951ace27913a1baf5a1e0&t=1643796&page=3)) {{:techtalk:evo:body:kickstand-spring-operation.jpg?400|Illustration by IXL2Relax at the XLForum}}{{:techtalk:evo:body:1998_sportster_jiffy_stand_pic1.jpg?direct&300|photo by Hippysmack of the XLFORUM}}  
 +{{:techtalk:evo:body:1998_sportster_jiffy_stand_pic2.jpg?direct&300|photo by Hippysmack of the XLFORUM}} 
 + 
 +====== Forward Controls ======
  
-but the bushings were added:\\ +===== Brake Pedal ===== 
-53158-98 . . BUSHING (2ea)\\+===== Clevis Pin =====
  
-so we might surmise that the kickstand mounting\\ +Dims were taken on used brake pedal and clevis pin below from a 1998 XL1200S.
-at the frame was enlarged on that model year to\\ +
-accomodate the bushings.\\+
  
-(See this [[http://xlforum.net/forums/showthread.php?t=1618492|discussion on the XLForum]])+{{:techtalk:evo:body:1998_xl1200s_brake_pedal_clevis_pin_dims-bores_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
  
-(See the [[techtalk:ref:body01#kickstand_spring_alternative|alternative spring choice]] in the REF section) 
  
 \\ \\

Trace: • EVO: Engine Mechanicals - Sub-03A • EVO: Transmission & Final Drive