Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
techtalk:evo:carb03 [2022/10/03 04:30] – [Subdocuments] hippysmacktechtalk:evo:carb03 [2024/01/02 22:09] (current) – hippysmack
Line 22: Line 22:
 |**1990-2003**|27004-88A \\ aluminum intake (27004-89) \\ sold as kit with \\ intake and carb seals|27009-86A|27010-86A|26995-86A|ring seal \\ 27002-89|:::| |**1990-2003**|27004-88A \\ aluminum intake (27004-89) \\ sold as kit with \\ intake and carb seals|27009-86A|27010-86A|26995-86A|ring seal \\ 27002-89|:::|
 |**2004-2006**|27024-04 \\ aluminum intake \\ sold as kit with \\ (map,seal,clip & screw)|27009-86A|27010-86A|26995-86A|ring seal \\ 27002-89|:::| |**2004-2006**|27024-04 \\ aluminum intake \\ sold as kit with \\ (map,seal,clip & screw)|27009-86A|27010-86A|26995-86A|ring seal \\ 27002-89|:::|
 +\\
  
 |  1986-1987 Sportster Intake Manifold (27004-86) ((photos courtesy of Stripped Down Cycles [[https://www.ebay.com/str/strippeddowncycles?_trksid=p2047675.m3561.l2563|Link to Ebay Store:]] ))  ||| |  1986-1987 Sportster Intake Manifold (27004-86) ((photos courtesy of Stripped Down Cycles [[https://www.ebay.com/str/strippeddowncycles?_trksid=p2047675.m3561.l2563|Link to Ebay Store:]] ))  |||
Line 33: Line 34:
  
 ===== 07 and Up Intake Manifold ===== ===== 07 and Up Intake Manifold =====
-2007-up (EFI) heads have a wider bolt pattern for the intake flanges. ((aswtacing of the XLFORUM http://xlforum.net/forums/showthread.php?p=5716946&highlight=intake+manifold#post5716946)) \\+2007-up (EFI) heads have a wider bolt pattern for the intake flanges. ((aswtacing of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-motor-top-end/195512-xr-heads-on-xl?highlight=intake+manifold#post4255444)) \\
 It's easier to get to the bolts on 07 and up intakes. \\ It's easier to get to the bolts on 07 and up intakes. \\
 All the 2007+ heads have their manifold mating surfaces milled down about 1/16" as compared with carb type heads. \\ All the 2007+ heads have their manifold mating surfaces milled down about 1/16" as compared with carb type heads. \\
Line 39: Line 40:
 If you don't get a wider manifold, there's a good chance you'll have issues with the seals being sucked into the intake ports on decel. If you don't get a wider manifold, there's a good chance you'll have issues with the seals being sucked into the intake ports on decel.
  
-{{:techtalk:evo:carb:intake_flanges_by_4-pac.jpg?direct&300|}} ((photo by 4-pac of the XLFORUM http://xlforum.net/forums/showthread.php?t=254258)) \\+{{:techtalk:evo:carb:intake_flanges_by_4-pac.jpg?direct&300|}} ((photo by 4-pac of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/53895-06-carb-to-07-fuel-injection-conversion?t=254258)) \\ 
 ====== Intake Flanges ====== ====== Intake Flanges ======
  

Trace: • REF: Engine Mechanicals - Sub-07A