| Both sides previous revisionPrevious revisionNext revision |
techtalk:ih:engmech01e [2022/03/24 21:13]
– [1979 XLS Cover] hippysmack |
|---|
| Previous revision |
techtalk:ih:engmech01e [2023/12/20 02:24] (current)
– hippysmack |
|---|
|
| ====== IH: Engine Mechanicals - Sub-01E ====== |
| ====== Ironhead Gearcase/Cam Cover Pics and Information ====== |
\\ |
| [[techtalk:ih:engmech01g|Click Here]] to go the Ironhead Gearcase/Cam Cover Removal and Installation page in the Sportsterpedia for fastener lists and gaskets. \\ |
====== Shifter Shaft / Brake Shaft Hole Bushings and Plugs ====== |
**1952-1974 Cam Covers**: \\ |
1952-1974 K models and Sportster use shifter shaft bushing (34037-52) in both the right case and the cam cover. \\ |
App. dims on bushing 34037-52) are 1/2" ID x 3/4" long. It should be close, if not match the -75 cover bushing dims. \\ |
This bushing is open ended for the long shift shaft to run through it. \\ |
|
**1975-1976 ====== Gearcase / Cam Covers**: \\Cover Parts List ====== |
1975All part numbers were gathered from period specific Sportster parts catalogs from 1957-1976 Sportsters use shifter shaft bushing (34037-52) in the right case 1985 including supplement and bushing (34037-75) in the cam cover. \\ |
As result of the Sportster going left side shift in 1975, the shifter shaft got shorter out of the right case. \\ |
The shaft end has linkages back to a crossover arm through the frame. \\ |
App. (only) dims are below for bushing (34037-75). It has one closed end which is installed on the outside of the coverupdated catalogs. \\ |
|
**1977-E1981 Cam Covers**^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&803|}}||||| |
| |Year Model|Cam / Gearcase Cover \\ Part Number|Casting Number|Gasket|Shifter \\ Shaft \\ Bushing| |
1977|1952-E1981 cam covers came 1956 K Models|25200-52|25202-52|25224-52| |
| Notes:|Replaced with a different bushing (2559425200-7552A in 1963. |||| |
| |1957-1962 XL/XLH/XLCH|25200-57|25202-52A|25224-52| |
| Notes:|Aluminum cover with single horizontal bar and square rear corner (not cut out)for a brake shaft. \\ |
Starting Uses generator "daisy wheel" oil deflector w/ sliding separator bushing/spring in 1977, the shifter shaft exits out the left case and the old then shifter shaft location in the cam cover became the brake shaft location. \\ |
This was the brake shaft design from 1977 Replaced by 25200-1979 (even though the rear brakes went hydraulic 63A in 1979)1968. |||| |
| |1963-1966 XLH \\ 1963-1967 XLCH|25200-63|25202-52A|25224-52| |
However, in 1980, the MoCo moved the brake operating lever to the trans sprocket | Notes:|Aluminum cover so the hole in the cam cover was now useless with single horizontal bar and square rear corner (1980-1985not cut out). \\ |
Dims: Uses generator slinger washer oil deflector w/ stationary bushing in cover. \\ Replaced by 25200-63A in 1968. |||| |
Cam Cover Bushing Bore|1967 XLH|25201-67|25202-52A|25224-52| |
| Notes:|1966 style single bar aluminum cover with rear cutout added around new starter. 7450" \\ Oil tank vent ((Scott 62375-62) added to the rear of the XLFORUM http://xlforumcover. net/forums/showthread.php?t=2074151)) \\ Replaced by 25201-67A in 1969.|||| |
Bushing OD |1968-1969 XLCH|25200-63A|02-68|25224-52| |
| Notes:|Aluminum cover with 6 horizontal ribs and square rear corner (before installingnot cut out).|||| |
| |1968-1970 XLH|25201-67A|02-68|25224-52| |
| Notes:|Aluminum cover with 6 horizontal ribs and rear cutout for starter.752" |||| |
| |1970 XLCH|25200-70|02-68| | |
| Notes:|Aluminum cover with 6 horizontal ribs and square rear corner ((Dims from Robison Motorcycles)no cut out). \\ |
Bushing ID (before installing): Previous boss for magneto redesigned to accept a circuit breaker. 6250" \\ Oil tank vent ((Scott 62375-57) added to the rear of the XLFORUM http://xlforumcover.net/forums/showthread.php?t=2074151)) |||| |
| |1971-1972 XLH \\ 1974 XLH|25201-71|71-25202|25224-52| |
Bushing Length| Notes:|Polished. 625" ((Dims from Robison Motorcycles)) |||| |
| |1971-1972 XLCH \\ 1974 XLCH|25200-71|71-25202|25224-52| |
| | Notes:| |||| |
**1980|1973 XLH|25201-E1981 Cam Covers**73 \\ black|71-25202|25224-52| |
| | Notes:| |||| |
| |1973 XLCH|25200-73 \\ black|71-25202|25224-52| |
In 1980, | Notes:| |||| |
| |1975-1976 XLH|25211-75|71-25202|25224-52| |
| Notes:|Shifter moved to the MoCo used left side of the bike in 1975.|||| |
| |1975-1976 XLCH|25205-75|71-25202|25224-52| |
| | Notes:| |||| |
| |1977-1978 XL \\ 1978 XLCH|25201-75|76-25202F|25244-52A| |
| | Notes:| |||| |
| |1977 XLCH|25200-75|76-25202F|25244-52A| |
| | Notes:|Replaced by 25201-75 (1978 parts sup).|||| |
| |1979 XL|25201-79 \\ 25201-79A|79-25202F|25244-52A| |
| Notes:|Polished. Original cover has a rubber plug reed type breather valve assembly (2522126909-7779A). \\ Replaced by 25201-79A which has a deeper boss in the now unused brake shaft hole in nosecone to mount the cam coverignition. \\ |
The brake shaft bushing was still installed presumably Kit includes a spacer (25262-80) to allow later covers extend ignition to be used on 1979 modelsoriginal location. \\ |
The rubber Rubber plug inserts into the bushing. \\ |
The parts books (198025221-198577) show the rubber plug sold for installed in 1979-E1981 Sportsterscover.|||| |
| |1979 XLCH|25200-79|79-25202|25244-52A| |
| Notes:|Polished. Original cover has a reed type breather valve assembly (26909-79A). \\ |
As usual, that means they expected one to upgrade Replaced by 25200-79A which has a deeper boss in the 1979 system nosecone to mount the 1980 systemignition. \\ Kit includes a spacer (25262-80) to extend ignition to original location.|||| |
|
**L1981|1979 XLS|25205-E1984 Cam Covers**: 79 \\ 25205-79A|79-25202|25244-52A| |
Once again | Notes:|Gray. Replaced by 25205-79A which has a change was made deeper boss in "how the nosecone to plug mount the ignition. \\ Kit includes a hole that goes nowhere"spacer (25262-80) to extend ignition to original location.|||| |
| |1980 XL|25208-80 \\ 25201-79A|80-25222|25244-52A| |
There may have been some problems with the rubber plug falling out or other| Notes:|Polished|||| |
| |1980 XLS|25209-80|80-25222|25244-52A| |
| Notes:|-80 parts book says, polished. The bushing and plug was deleted from the cover-81 book says black.\\|||| |
The hole was still there but threaded |E1981 XL|25227-81|81-25223|25244-52A| |
| | Notes:|Polished. Angle cut upper feed galley slot. No pins in cam bushings.|||| |
| |E1981 XLS|25229-81|81-25223|25244-52A| |
| | Notes:|Black. Angle cut upper feed galley slot.|||| |
| |L1981-1982 XLS|25209-81|25222-81|25263-81| |
| Notes:|Black. Straight cut upper feed galley slot. No casting for metal plug (2506), tach drive. No pins in cam bushings. \\ 7/16"-14 x 114x1/2" hex socket bolt, which screws into the cam coverallen hd plug screw (2506) installed thru 1985 in place of rubber plug.|||| |
|L1981-E1984 XL \\ |
L1983-1984E1984 XLS/XLX|25208-1985 covers did not use a plug nor did they have a hole for a plug even though the parts books show the plug for L8181|25222-85 models81|25263-81| |
| Notes:|Polished. \\No casting for tach drive. No pins in cam bushings.|||| |
|
**1975|1983-1976 Sportster 1985 XLX|25207-83| shifter shaft**: \\ |25263-81| |
{{| Notes:techtalk:ih:engmech:1975|Kit w/ aluminum finish. No casting for tach drive.|||| |
|L1984 XLX|25207-1976_shifter_shaft_bushing_3403784|25222-75_by_robisonmotorcycles_pic1.jpg?direct&30084A|}} {{25263-81| |
| Notes:techtalk:ih:engmech:1975|Aluminum finish. Replaced by 25207-1976_shifter_shaft_bushing_3403784A (-75_by_robisonmotorcycles_pic2.jpg?direct&30085A parts book)|||| |
|}} {{:techtalk:ih:engmech:1975L1984 XL/XLS|25208-1976_shifter_shaft_bushing_3403784|25222-75_by_robisonmotorcycles_pic3.jpg?direct&30084A|25263-81|}} \\ |
|
{{:techtalk| Notes:ih:engmech:1975|Polished. Replaced by 25219-1976_shifter_shaft_bushing_3403786 (-75_by_robisonmotorcycles_pic4.jpg?direct&30085A parts book)|}} {{:techtalk:ih:engmech:1975||| |
|1985 XLX|25207-1976_shifter_shaft_bushing_3403784A|25222-75_by_robisonmotorcycles_pic5.jpg?direct&30084A|}} {{:techtalk25263-81| |
| Notes:ih:engmech:1975|Black.|||| |
|1985 XL/XLS|25208-1976_shifter_shaft_bushing_3403784A|25222-75_by_robisonmotorcycles_pic684A|25263-81| |
| Notes:|Polished. jpg?direct&300Replaced by 25219-86 (-85A parts book)||||}} \\ |
|
| ====== Internal Comparisons ====== |
You can interchange some covers if you are not concerned about the look of a stocker for your year bike (better resale trying to stay stock). ((Monte03 of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.php?p=1284165sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/52221-cams-cover-interchange#post1284165post1084712)) \\ |
|
| Also be aware that some covers had the round cut out for the electric starter XLH that came out in 1967. \\ |
|
| (so the cam cover and the right case half are a match in tolerances) \\ |
|
52-78 cover had only one breather port at 6:00. ((Dr Dick of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) \\ |
| 79-85 had two. One at 6:00 and one at 10:00. \\ |
| 52-76 uses .625" pinion bushing bore. \\ |
| 77-85 uses .562" pinion bushing bore. \\ |
|
| 1952-1956 Cam Cover - casting: 25202-52 ((photo by Dr Dick of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) | 1957-1962 Cam Cover - casting: 25202-52A ((photo by ironheadjunkie of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/132743-oil-line-routing/page2?t=1421916&page=2)) | 1963-1967 Cam Cover - casting: 25202-52A((photo by Dr Dick of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) | |
| |{{:techtalk:ih:engmech:cam_cover_52-56_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ih:engmech:cam_cover_1_25202-52a_by_ironheadjunkie.jpg?direct&300|}}|{{:techtalk:ih:engmech:cam_cover_63-67_by_dr_dick.jpg?direct&300|}}| |
|
| 1968-1970 Cam Cover - casting: 02-68 ((photo by Dr Dick of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) | 1971-1976 Cam Cover - casting: 25202-71 ((photo by Dr Dick of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) | 1977-1978 Cam Cover - casting 76-25202F ((photo by DirtyCory of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/127032-getting-this-78-back-to-the-way-it-should-be/page9?t=1297584&page=9)) | |
| |{{:techtalk:ih:engmech:cam_cover_68-70_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ih:engmech:cam_cover_71-76_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ih:engmech:cam_cover_77-78_by_dr_dick.jpg?direct&300|}}| |
|
| 1979-1980 Cam Cover - casting: 79-25202 ((photo by Dr Dick of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) | 1981 Cam Cover - casting: 81-25223 ((photo by Scott of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/197215-cam-cover-id-help-please-warning-huge-pics?t=2073823)) | L1984-1985 Cam Cover - casting: 25222-84A ((photo by Dr Dick of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) \\ (no date code below casting) | |
| |{{:techtalk:ih:engmech:cam_cover_79-80_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ih:engmech:1981_cam_cover_by_scott.jpg?direct&300|}}|{{:techtalk:ih:engmech:cam_cover_l84-85_by_dr_dick.jpg?direct&300|}}| |
|
| ====== 1957-1970 Cam Covers ====== |
1957 thru 1970 Sportsters had cams designed for an ignition to be mounted on top of the cam cover. ((Monte03 of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/52221-cams-cover-interchange?t=230843)) \\ |
| These cams are not interchangeable with post 1971 motors (what can be called the 'cone' cam cover). \\ |
| Early XLs had XL cams, 1966 thru the 1970s had hotter cams known as P cams. \\ |
|
| P cams are frequently seen for sale on ebay. \\ |
| When hunting for parts you want to ask, "Pre 1971 or Post 1971" for cams and covers including the sprocket cover. \\ |
|
| ===== 1957-1962 XL/XLH/XLCH Cover ===== |
| Part number (25200-57). Casting number is (25202-52A). \\ |
|
| {{:techtalk:ih:engmech:1957-1962_xl-xlh-xlch_cam_cover_25200-57_by_animalhouse2010_pic4.jpg?direct&300|}} {{:techtalk:ih:engmech:1957-1962_xl-xlh-xlch_cam_cover_25200-57_by_animalhouse2010_pic5.jpg?direct&300|}} {{:techtalk:ih:engmech:1957-1962_xl-xlh-xlch_cam_cover_25200-57_by_animalhouse2010_pic6.jpg?direct&300|}} \\ |
|
===== 1963-1966 XLH, 1963-1969 1967 XLCH Cover ===== |
| Part Number (25200-63). Casting number is (25202-52A). \\ |
|
Click on a pic to enlargeexpand: ((photos photo courtesy of Ebay seller, Motorcycle Dreams. [[https://www.ebay.com/str/motorcycledreams|Link to Ebay Store:]] )) \\ |
{{:techtalk:ih:engmech:1963-1966_xlh_1963-1969_xlch_cam_cover_252001967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1963-1966_xlh_1963-1969_xlch_cam_cover_252001967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic2.jpg?direct&300|}} {{:techtalk:ih:engmech:1963-1966_xlh_1963-1967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic3.jpg?direct&300|}} \\ |
|
{{:techtalk:ih:engmech:1963-1966_xlh_1963-1969_xlch_cam_cover_252001967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic363_by_motorcycle_dreams_pic4.jpg?direct&300|}} {{:techtalk:ih:engmech:1963-1966_xlh_1963-1969_xlch_cam_cover_252001967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic463_by_motorcycle_dreams_pic5.jpg?direct&300|}} {{:techtalk:ih:engmech:1963-1966_xlh_1963-1969_xlch_cam_cover_252001967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic563_by_motorcycle_dreams_pic6.jpg?direct&300|}} \\ |
|
===== 1967 -1970 XLH Cover ===== |
Cover part Part number (25201-67). Casting number is (0225202-6852A). Top rear is cut out for the electric starter. \\ |
Same as 1967 -up XLH motors all vent XLCH but has the oil tank air space to the cam chest at a 90° fitting on the back of the cam cover. \\ |
The previous year's vent location on the top of the rear engine case was deleted. \\ |
1969 covers had an oil tank vent fitting (62375cut-62). \\ |
1970 XLH cover had an oil tank fitting (62375-57). \\ |
Both fittings are 1/8"-27 NPT to 1/4" hose barb 90° elbowsout for electric start. \\ |
|
Click on a pic to enlarge{{:techtalk:ih:engmech:1967_xlh_cam_cover_pic1_by_market406.jpg?direct&300|}} ((photos photo courtesy of Ebay seller, animalhouse2010, market406. [[https://www.ebay.com/strsch/animalhouse2010market406/m.html?_trksid_nkw=&_armrs=1&_ipg=&_from=p2047675.l2563|Link to Items for Sale page]] )) {{:techtalk:ih:engmech:1967_xlh_cam_cover_pic3_by_market406.jpg?direct&300|}} ((photo courtesy of Ebay storeseller, market406. [[https://www.ebay.com/sch/market406/m.html?_nkw=&_armrs=1&_ipg=&_from=|Link to Items for Sale page]] )) \\ |
| |
| ===== 1968-1969 XLCH Cover ===== |
| Cover part number (25200-63A). Casting number is (02-68). \\ |
| The oil tank is still vented to the fitting at the top of the right case behind the rear cylinder. \\ |
| Looks similar to the 68 H cover with exceptions. \\ |
| The XLCH cover has a squared (uncut) rear corner, no 90° fitting on back and the ignition boss on top is set up to accept a magneto. \\ |
| |
| Click on any pic to enlarge: ((photos courtesy of Brewer's Performance Inc. in Laura, Ohio [[http://www.brewersperformance.com/|Link to website]] )) \\ |
{{:techtalk:ih:engmech:19671968-1970_xlh_cam_cover_252011969_xlch_cam_cover_25200-67_pic1_by_animalhouse201063_pic1_by_shopanuck.jpg?direct&300|}} {{:techtalk:ih:engmech:19671968-1970_xlh_cam_cover_252011969_xlch_cam_cover_25200-67_pic2_by_animalhouse201063_pic2_by_shopanuck.jpg?direct&300|}} \\ |
| |
| {{:techtalk:ih:engmech:1968-1969_xlch_cam_cover_25200-63_pic3_by_shopanuck.jpg?direct&300|}} {{:techtalk:ih:engmech:1968-1969_xlch_cam_cover_25200-63_pic4_by_shopanuck.jpg?direct&300|}} \\ |
| |
| ===== 1968-1970 XLH Cover ===== |
| Cover part number (25201-67A). Casting number is (02-68). Top rear corner is cut out for the electric starter. \\ |
| The oil tank is vented to the cam chest at a 90° fitting on the back of the cam cover. \\ |
| 1968-1969 covers came with oil tank vent fitting (62375-62). \\ |
| 1970 XLH covers came with oil tank fitting (62375-57). \\ |
| Both fittings are 1/8"-27 NPT to 1/4" hose barb 90° elbows. \\ |
|
{{:techtalk:ih:engmech:19671968-1970_xlh_cam_cover_25201-67_pic3_by_animalhouse201067a_pic1_by_flashback_inc.jpg?direct&300|}} ((photo courtesy of Flashback Enterprises in Imlay City, MI, [[https://www.ebay.com/str/flashbackenterprisesinc?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] )) |
{{:techtalk:ih:engmech:19671968-1970_xlh_cam_cover_25201-67_pic4_by_animalhouse201067a_pic2_by_flashback_inc.jpg?direct&300|}} {{((photo courtesy of Flashback Enterprises in Imlay City, MI, [[https:techtalk:ih:engmech:1967-1970_xlh_cam_cover_25201-67_pic5_by_animalhouse2010//www.ebay.jpgcom/str/flashbackenterprisesinc?direct&300_trksid=p2047675.m3561.l2563|}} Link to Ebay Store]] )) \\ |
|
{{:techtalk:ih:engmech:19671968-1970_xlh_cam_cover_25201-67_pic6_by_animalhouse201067a_pic1_by_cyclewarehouse.jpg?direct&300|}} {{((photo courtesy of Ebay seller, cyclewarehouse. [[https:techtalk:ih:engmech:1967-1970_xlh_cam_cover_25201-67_pic7_by_animalhouse2010//www.ebay.com/sch/cyclewarehouse/m.jpghtml?direct_nkw=&300_armrs=1&_ipg=&_from=|}} Link to Items for Sale]] )) {{:techtalk:ih:engmech:19671968-1970_xlh_cam_cover_25201-67_pic8_by_animalhouse201067a_pic3_by_flashback_inc.jpg?direct&300|}} ((photo courtesy of Flashback Enterprises in Imlay City, MI, [[https://www.ebay.com/str/flashbackenterprisesinc?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] )) \\ |
|
| ===== 1970 XLCH Cover ===== |
| Cover part number (25200-70). Casting number (02-68). TOP REAR IS NOT CUT for electric start. \\ |
| 1970-up XLH and XLCH motors all now vent the oil tank air space to the cam chest at a 90° fitting on the back of the cam cover. \\ |
| The previous year's vent location on the top of the rear engine case was deleted for XLCH. \\ |
| The fitting (62375-57) is a 1/8"-27 NPT to 1/4" hose barb 90° elbow. \\ |
|
Click on a pic to enlarge: ((pics by Scott of the XLFORUM httphttps://www.xlforum.net/forumsforum/showthread.phpsportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/197215-cam-cover-id-help-please-warning-huge-pics?t=2073823)) \\ |
| {{:techtalk:ih:engmech:1970_xlch_cam_cover_25200-70_pic1_by_scott.jpg?direct&300|}} {{:techtalk:ih:engmech:1970_xlch_cam_cover_25200-70_pic2_by_scott.jpg?direct&300|}} {{:techtalk:ih:engmech:1970_xlch_cam_cover_25200-70_pic3_by_scott.jpg?direct&300|}} \\ |
|
|
| Fasteners: (8) cover screws, (2) generator mounting bolts and (2) solid dowel pins (used at front and rear of cover). \\ |
| [[techtalk:ih:engmech01g#cam_cover_fastener_list|Click Here]] to see full fastener list. \\ |
|
Click on a pic to enlarge: ((photos courtesy of NitroFrankie Go-Fast HD, [[https://www.ebay.com/sch/m.html?item=194837126341&_ssn=ct_kustoms&_ipg=200&rt=nc|Ebay Items for Sale Page]] )) \\ |
{{:techtalk:ih:engmech:1975-1976_xlh_cam_cover_25211-75_by_bad_ass_cycles_etc_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1975-1976_xlh_cam_cover_25211-75_by_bad_ass_cycles_etc_pic2.jpg?direct&300|}} \\ |
|
{{:techtalk:ih:engmech:1975-1976_xlh_cam_cover_25211-75_by_bad_ass_cycles_etc_pic3.jpg?direct&300|}} {{:techtalk:ih:engmech:1975-1976_xlh_cam_cover_25211-75_by_bad_ass_cycles_etc_pic4.jpg?direct&300|}} {{:techtalk:ih:engmech:1975-1976_xlh_cam_cover_25211-75_by_bad_ass_cycles_etc_pic5.jpg?direct&300|}} \\ |
|
| ===== 1975-1976 XLCH Cover ===== |
|
|
| {{:techtalk:ih:engmech:1979_xls_cam_cover_25205-79_by_harley-davidson_parts_accessories_pic4.jpg?direct&300|}} {{:techtalk:ih:engmech:1979_xls_cam_cover_25205-79_by_harley-davidson_parts_accessories_pic5.jpg?direct&300|}} {{:techtalk:ih:engmech:1979_xls_cam_cover_25205-79_by_harley-davidson_parts_accessories_pic6.jpg?direct&300|}} \\ |
|
| ===== 1980 XLH Cover ===== |
| Part number for cover (25208-80). Casting number (80-25222). \\ |
|
|
| Click on a pic to enlarge: ((photos courtesy of NitroFrankie Go-Fast HD, [[https://www.ebay.com/sch/m.html?item=194837126341&_ssn=ct_kustoms&_ipg=200&rt=nc|Ebay Items for Sale Page]] )) \\ |
{{:techtalk:ih:engmech:1981e_xls_cam_cover_-_black_-_25229-81_by_nitrofrankie_go-fast_hd_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1981e_xls_cam_cover_-_black_-_25229-81_by_nitrofrankie_go-fast_hd_pic2.jpg?direct&300|}} \\ |
|
| {{:techtalk:ih:engmech:1981e_xls_cam_cover_-_black_-_25229-81_by_nitrofrankie_go-fast_hd_pic2.jpg?direct&300|}} |
| {{:techtalk:ih:engmech:1981e_xls_cam_cover_-_black_-_25229-81_by_nitrofrankie_go-fast_hd_pic3.jpg?direct&300|}} {{:techtalk:ih:engmech:1981e_xls_cam_cover_-_black_-_25229-81_by_nitrofrankie_go-fast_hd_pic4.jpg?direct&300|}} \\ |
|
|
| {{:techtalk:ih:engmech:1985_xl-xls_cam_cover_25208-84a_by_nitrofrankie_go-fast_hd_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1985_xl-xls_cam_cover_25208-84a_by_nitrofrankie_go-fast_hd_pic2.jpg?direct&300|}} {{:techtalk:ih:engmech:1985_xl-xls_cam_cover_25208-84a_by_nitrofrankie_go-fast_hd_pic3.jpg?direct&300|}} \\ |
|
| L1984-1985 cover casting# (25222-84A) ((photo courtesy of NitroFrankie Go-Fast HD, [[https://www.ebay.com/sch/m.html?item=194837126341&_ssn=ct_kustoms&_ipg=200&rt=nc|Ebay Items for Sale Page]] )) | 1986-1990 cover casting# (25222-8484A) ((photo courtesy of DeadpartsMC, [[https://www.ebay.com/str/deadpartsmc|Link to Ebay Store]] )) | |
| |{{:techtalk:ih:engmech:1985_xl-xls_cam_cover_25208-84a_by_nitrofrankie_go-fast_hd_pic4.jpg?direct&300|}}|{{:techtalk:evo:engmech:1986-1990_sportster_cam_cover_25219-86_by_deadpartsmc_pic5.jpg?direct&300|}}| |
|
