Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| techtalk:ih:engmech01g [2025/08/01 16:03] – [Breaker Points/Nosecone Ignition Seal] hippysmack | techtalk:ih:engmech01g [2025/08/01 19:40] (current) – [Inspection] hippysmack | ||
|---|---|---|---|
| Line 4: | Line 4: | ||
| ====== Ironhead Gearcase/ | ====== Ironhead Gearcase/ | ||
| + | ====== Cam/ | ||
| + | Article by Dr Dick of the XLFORUM ((https:// | ||
| + | |||
| + | * Take the cam cover off without dropping anything in the drain pan or on the floor while preserving where all the shims are positioned. | ||
| + | * Try not take the cams out unless you Need to. | ||
| + | * Strip all needed parts to get to the cam cover only. | ||
| + | * Carb | ||
| + | * Mag | ||
| + | * Exhaust | ||
| + | * Pegs | ||
| + | * Kicker | ||
| + | * Shifter | ||
| + | * Breather tube | ||
| + | * Generator | ||
| + | * Kicker cover | ||
| + | * Pushrods | ||
| + | * Remove all screws from cam cover. | ||
| + | * Now look in the gap, and with a skinny screw driver, push all the cams back into the engine so that they won't come out with the cover. | ||
| + | |||
| + | |||
| + | |||
| + | | Gently work the cover to this position | ||
| + | |{{: | ||
| + | |||
| + | * Now, you will be able to see the shims if there are any in there. | ||
| + | * Use an ice pick to work any shims, that are hanging on the cover bushing flanges, back onto the cams. | ||
| + | * Make sure the cams hang inside the motor using the skinny screwdriver again as you work the cover off. \\ Note that the cover is still engaged to the cams and that they are slid fully into the motor side. | ||
| + | |||
| + | | Keep this up until you have the cover off ((photo by Dr Dick of the XLFORUM https:// | ||
| + | |{{: | ||
| + | |||
| + | ====== Inspection ====== | ||
| + | * **Inspect the cam bushings**. Check the clearances per the service manual and replace any out of service bushings. Also check for scoring or scratches. [[techtalk: | ||
| + | * **Inspect the point cover/ | ||
| + | * Look for ID leaks; a marred cam journal, seal lip not getting up on the full journal diameter or a missing dog bone thrust plate on far side of cam. ((Dr Dick of the XLFORUM https:// | ||
| + | * Look for OD leaks; the seal bore nicked, tearing the seal OD when installing it. | ||
| + | * Look for scratches, gouges or wear marks on the cam shaft where the seal seats. If there are any, they need to be removed or the shaft changed. Also check if there are any gouges or cracks around the outside diameter of where the seal fits in (bore). These can be put there during seal removal and let oil seep out around the outside of the seal. They can usually be scraped or filed back flat. You can make a scraper by grinding the teeth off the end of a three-sided file. | ||
| + | * **Inspect the breather vent/ | ||
| ====== Preparation ====== | ====== Preparation ====== | ||
| ===== Breaker Points/ | ===== Breaker Points/ | ||
| Line 22: | Line 60: | ||
| ==== Seal removal/ | ==== Seal removal/ | ||
| - | === Inspection === | ||
| - | * __Look for ID leaks__; a marred cam journal, seal lip not getting up on the full journal diameter or a missing dog bone thrust plate on far side of cam. ((Dr Dick of the XLFORUM https:// | ||
| - | * Look for scratches, gouges or wear marks on the cam shaft where the seal seats. If there are any, they need to be removed or the shaft changed. \\ Also check if there are any gouges or cracks around the outside diameter of where the seal fits in (bore). \\ These can be put there during seal removal and let oil seep out around the outside of the seal. They can usually be scraped or filed back flat. \\ You can make a scraper by grinding the teeth off the end of a three-sided file. | ||
| - | |||
| === Removal === | === Removal === | ||
| * With the cover installed: (do-able but arguably not the best way) | * With the cover installed: (do-able but arguably not the best way) | ||
| Line 42: | Line 76: | ||
| ===== Cam Cover Gasket ===== | ===== Cam Cover Gasket ===== | ||
| - | [[techtalk: | ||
| - | |||
| **Make sure to use the correct gasket for your engine/ | **Make sure to use the correct gasket for your engine/ | ||
| + | [[techtalk: | ||
| There were changes to the upper feed galley that dictate a specific gasket, especially between 1979-1982 models. \\ | There were changes to the upper feed galley that dictate a specific gasket, especially between 1979-1982 models. \\ | ||
| The upper oil feed galley was redesigned during the 1979-1982 and according to the MoCo, the gasket must fit the case design. \\ | The upper oil feed galley was redesigned during the 1979-1982 and according to the MoCo, the gasket must fit the case design. \\ | ||
| + | [[techtalk: | ||
| ====== Installing the Cover ====== | ====== Installing the Cover ====== | ||
| Line 54: | Line 88: | ||
| The rods help the cover come up evenly without binding anything. \\ | The rods help the cover come up evenly without binding anything. \\ | ||
| Install several mounting screws in unused holes to "just snug" then remove all the rods and install all the other mounting screws "just snug". \\ | Install several mounting screws in unused holes to "just snug" then remove all the rods and install all the other mounting screws "just snug". \\ | ||
| - | Then use the torque specs and torque sequence | + | Then use the torque specs and torque sequence |
| + | |||
| + | {{: | ||
| ===== Cam Cover Fastener List ===== | ===== Cam Cover Fastener List ===== | ||
