Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
techtalk:ref:engctl50f [2020/01/11 23:38] – ixl2relaxtechtalk:ref:engctl50f [2024/01/14 16:17] (current) – hippysmack
Line 1: Line 1:
 [[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]] [[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]]
-====== REF: Engine Control 50f ======+====== REF: Engine Control - Sub-50F ======
  
 \\ \\
Line 10: Line 10:
  
 It is the responsibility of the user doing the tuning to evaluate the information they find in order to know that it is compatible with their engine configuration and riding circumstances. Also realize that those who are aggressive riders will often tune right to the edge of usability in searching for a bit more power or responsiveness, while other, less agressive riders, may prefer to tune their timing to avoid problems from some variables and factors that might push it over the edge. It is the responsibility of the user doing the tuning to evaluate the information they find in order to know that it is compatible with their engine configuration and riding circumstances. Also realize that those who are aggressive riders will often tune right to the edge of usability in searching for a bit more power or responsiveness, while other, less agressive riders, may prefer to tune their timing to avoid problems from some variables and factors that might push it over the edge.
 +
 +If, somehow, you overlooked these, be sure to read these comments:\\
 +[[techtalk:ref:engctl01#why_adjust_the_spark_timing|Why Adjust The Spark Timing?]] by **RacerWill**\\
 +[[techtalk:ref:engctl01#too_much_advance_timing|Too Much Advance Timing]] by **Aaron Wilson**\\
 +[[techtalk:ref:engctl01#manifold_absolute_pressure_-vs-_vacuum_reading|Manifold Absolute Pressure -vs- Vacuum Reading]] by **RacerWill**\\
  
 ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~
 +
 \\ \\
  
-http://xlforum.net/forums/showthread.php?t=1422868\\+https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-electrical/sportster-motorcycle-electrical-and-ignition/132778-daytona-tc88a-do-your-own-mapping-tips-questions?t=1422868\\
  
 **Post#117 - Xena commenting on 'Best Map' - May 2012**\\ **Post#117 - Xena commenting on 'Best Map' - May 2012**\\
Line 57: Line 63:
  
 ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~
 +
 \\ \\
  
Line 77: Line 84:
  
 ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~
 +
 \\ \\
  
  
-http://xlforum.net/forums/showthread.php?t=18702+https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-electrical/sportster-motorcycle-electrical-and-ignition/11396-final-tc88a-map-program-lots-of-other-data?t=18702 
 + 
 +**Post#396 - JBM - Aug 2007** - Spark advance for manifold pressure below 16 In/Hg\\ 
 +To me it's still a mystery why TC88A doesn't calibrate values below 16 in/hg. In HD's own Screamin' Eagle Ignition Race Tuner (SERT) you may customize the stock ignition module with SE ignition curves and calibrate map values in the range of 0-16 in/hg also. The SERT/OE range is 0-103 Kpa (0-30 in/hg), while the Twintec range is 54-103 Kpa (16-30 in/hg). SERT has 9 rows, and four of those are below the TC88A lowest row. I ran SERT before I installed TC88A. 
 + 
 +**Post#412 - JBM - Aug 2007**\\ 
 +This morning I sent an email to Chris Schroeder from Daytona Twin Tec and asked about those advance issues for manifold pressures below 16 In/Hg in TC88A. With his permission I publish his reply:\\ **Very few engines require additional spark advance below 16 in-Hg manifold pressure. The TC88A uses the 16 In-Hg value for all lower pressures. As further clarification, internal cylinder pressure is so low under these conditions (MAP below 16 in-Hg) that maximum spark advance values near 45 degrees are reasonable for most engine applications. Since 45 degrees is the maximum advance the TC88 series is capable of, there is no reason to complicate the advance tables. Even higher advance values yield little benefit.** 
  
 **Post#1005 - Turbota - June 2010**\\ **Post#1005 - Turbota - June 2010**\\
Line 145: Line 160:
  
 ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~
 +
 \\ \\
  
  
-http://xlforum.net/forums/showthread.php?t=1419021+https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-electrical/sportster-motorcycle-electrical-and-ignition/132607-tc-88a-chat?t=1419021
  
 **Post#235 - Rico05r**\\ **Post#235 - Rico05r**\\
Line 156: Line 172:
  
 ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~ ~~~~
 +
 \\ \\
  
  
-http://xlforum.net/forums/showthread.php?t=1422868+https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-electrical/sportster-motorcycle-electrical-and-ignition/132778-daytona-tc88a-do-your-own-mapping-tips-questions?t=1422868
  
 **Post#193 - Highly-Dangerous mentions Turbota's maps: MAP Modified 35 / MAP Modified 33 / MAP Modified 35 Revised** - Nov 2019\\ **Post#193 - Highly-Dangerous mentions Turbota's maps: MAP Modified 35 / MAP Modified 33 / MAP Modified 35 Revised** - Nov 2019\\

Trace: • REF: Engine Mechanicals - Sub-03A • REF: Tools - 145 • EVO: Engine Mechanicals - Sub-01F