REF: Tools - 160 - Sportsterpedia

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

[[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]]
====== REF: Tools - 160 ======
====== Hand Operated Vacuum Pump / Testers ======

====== Vacuum Pump ======

A hand operated vacuum pump is a versatile tool that can be used to test a variety of automotive systems and perform a number of useful tasks. ((MityVac MV-8000 Operating Manual)) \\
Though the pump has obvious uses for testing various vacuum motors, control valves and vacuum sources, it's applications don’t end there. \\
Almost any part or system that requires proper sealing vacuum to operate can be tested with the vacuum pump. \\
The pump and it's accessories also transfer fluids, help to bleed brakes and aid in other tasks. \\
The pump also meets diagnostic tool requirements when such tools are specified for some state vehicle inspection
programs. \\

The pump is easily held in your hand, and when the handle is squeezed, vacuum is produced at the front fitting. \\
If the front fitting of the pump is connected to a closed container or system, the gauge will show the vacuum level created. \\
The pump is simple to use although successive pumping can be tough on your wrist muscles. ((MityVac MV-8000 Operating Manual)) \\
In most applications on Sportsters, it’s attached directly to a brake bleeder screw, or VOES or MAP sensor to create a suction for bleeding fluid or testing diagnostics. \\
   - When vacuum is desired for a test, the movable handle of the pump is simply squeezed with your hand, as in clenching your fist. \\ Continue strokes until the desired vacuum is indicated on the gauge.
   - The pump can be connected into a vacuum circuit and used to measure existing amounts of vacuum, just as any vacuum gauge would be used. \\ When used this way, do not pump the handle, or incorrect readings may result.
   - The vacuum gauge can be useful for detecting a fluctuating vacuum supply or a leaky hose.

===== Proper Care and Maintenance =====

Handle the vacuum pump carefully and do not or handle it roughly as the gauge accuracy may be affected. ((MityVac MV-8000 Operating Manual)) \\
Silicone oil is suggested to lubricate the pump / O-rings if needed. \\
DOT 5 brake fluid (silicone based) or vegetable salad oil can also be used as lubricant in absence of silicone oil. \\
Do not use petroleum based fluids or spray lubricants (WD-40, motor oil, etc.), as these can damage the seals in the pump. \\

====== Dissecting the MityVac 8000 ======

{{:techtalk:ref:tools:mityvac_mv8000_pic1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\

{{:techtalk:ref:tools:mityvac_mv8000_pic2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:mityvac_mv8000_pic3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:mityvac_mv8000_pic4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\

{{:techtalk:ref:tools:mityvac_mv8000_pic5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:mityvac_mv8000_pic6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:mityvac_mv8000_pic7_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
 

\\

[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]

Trace: • REF: Tools - 160 • IH: Engine Mechanicals - Sub-09T • REF: Service Procedures 22 • IH: Engine Mechanicals - Sub-09B • IH: Engine Mechanicals - Sub-09A • IH: Engine Mechanicals - Sub-09J